QSC Logo
QSC - Hear the power of technology.
 
 
 
HomeProductsRMX SeriesRMX 4050HD › Specifications
  RMX 4050HD
 
  Specifications

 
 
SPECIFICATIONS RMX 4050HD RMX 4050HD / CE Compliant
STEREO MODE (Both Channels Driven)
8 ohms
FTC 20 Hz - 20 kHz, 0.1% THD
EIA 1 kHz, 0.1% THD

800 W
850 W

650 W

4 ohms
FTC 20 Hz - 20 kHz, 0.1% THD
EIA 1 kHz, 0.1% THD

1300 W
1400 W

1300 W

2 ohms
FTC 20 Hz-20 kHz 0.1% THD
EIA 1 kHz 1% THD

1600 W
2000 W

1600 W
2000 W
BRIDGE MONO MODE
8 ohms
FTC 20 Hz-20 kHz 0.1% THD
EIA 1 kHz 0.1% THD

2600 W
2800 W

2600 W
2800 W
4 ohms
EIA 1 kHz 1% THD

4000 W

4000 W
Distortion (SMPTE-IM) Less than 0.02%
Distortion (Typical)
20 Hz-20 kHz: 10 dB below rated power
1 kHz and below: full rated power

Less than 0.02% @ 4 ohms, less than 0.01% @ 8 ohms
Less than 0.02% @ 4 ohms, less than 0.01% @ 8 ohms
Frequency Response 20 Hz to 20 kHz, 8 ohms, LF filter bypassed, +0/-1 dB
5 Hz to 50 kHz, 8 ohms, LF filter bypassed, +0/-3 dB
Damping Factor Greater than 250 @ 8 ohms
Noise (unweighted) 100 dB below rated output (20 Hz - 20 kHz, 8 ohm load)
Input Impedance 20k ohm balanced, 10k ohm unbalanced
Input Sensitivity 1.25 Vrms for 800 W into 8 ohms 1.12 Vrms for 650 W into 8 ohms
Voltage Gain 64x (36 dB) for 8 ohm load
Controls Front:
Controls Rear:
AC power switch, Ch. 1 and Ch. 2 gain control
10-pole DIP switch featuring LF filter on/off, LF filter 30/50 Hz, Clip Limiter on/off controls for each channel and switches for selecting Stereo, Parallel, or Bridge mode. Push-button circuit breaker for each channel.
Indicators Power-On: Green LED, Protect: Red LED
Signal -30dB: Yellow LED, Clip: Red LED
Connectors Input:
Connectors Output:
XLR female, TRS (1/4-inch), and barrier-strip screw terminals, each channel
Binding posts and Speakon® outputs (Ch. 1 Speakon wired for biamp)
Cooling Continuously variable-speed fan, rear-to-front air flow
Amplifier Protection Short circuit, open circuit, thermal, ultrasonic, and RF protection. Stable into reactive or mismatched loads
Load Protection On/off muting, DC fault output crowbar
Power Requirements 100, 120 or 240 Volts AC (+/-10%) 50-60 Hz (factory configured) 240 Volts AC (+/-10%) 50-60 Hz
Dimensions 19" 19.0" (48.3 cm) wide, 5.25" (13.3 cm) tall, 15.9" (40.39 cm) overall depth
Weight 68 lb (30.84 kg) net, 77 lb (34.43 kg) shipping
 
   
     
 
© 2008 QSC Audio. All Rights Reserved.